Understanding Plumbing Basics is Crucial for Installing a Bathtub
Understanding Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
Everyone has their personal way of thinking on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately difficult job. If the old bathtub is conveniently accessible, the job can relocate easily; if you need to open a wall surface to remove the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the job is within a residence handyman's abilities, although you will require an assistant to move out the old tub and set in the brand-new one. Make certain you have actually qualified on your own for the job as well as are comfortable trying it. Rather than working with a specialist to take control of a halfway-completed task, it is much better to take into consideration using one before you begin. Possibilities are you may require an expert plumber to make tube links.
This article will aid you mount a brand-new bath tub in your shower room if you have already gotten a brand-new tub and do not need to transform the setup of your previous water system pipelines.
Your tools and material checklist should comprise the following:
Getting ready for the Installment
First of all, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to see to it that if the tap features a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to stop stress on the tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be rather bothersome because of the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have been eliminated, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Prior to moving on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Using the two wood boards under its feet, place the tub in the called for placement. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bath tub till the spirit level reviews level.
To mount faucets, fit all-time low of the outermost versatile tap adapter to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Turn on the water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as likewise inspect the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub ought to wait till the tub has been utilized a minimum of once as this will certainly resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Protect the faucet in place with the supplier supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap adapters. The previous type must be attached to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a stiff seal, causing the water to penetrate the wall between the bath as well as the tiling, causing issues with moisture as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and installations. They are marketed in tubes as well as cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the activity experienced when the tub remains in use. The sealant can break fairly very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Post a remark down below. We'd be glad to see your feelings about this page. We hope to see you back again soon. Appreciated our review? Please share it. Let somebody else check it out. Thanks for taking the time to read it.
Contact Report this page